We take moisture out of the air.
Drynex fights humidity before it becomes condensation, corrosion, mould or frost. We supply desiccant dehumidifiers that keep air dry in cold, damp and hard-to-reach spaces where ordinary dehumidifiers stop working.
Exclusive Canadian DistributorBry-Air MiniPAC® compact desiccant dehumidifiers
Engineered humidity control for Canadian projects.
Drynex supplies, sizes and supports the Bry-Air MiniPAC line across Canada. Eight ETL-certified models from 100 to 2,700 CFM, selected by a professional engineer and backed by fast parts support.
In stock. On your site fast.
Schedules slip and moisture problems don't wait. We keep MiniPAC units in stock so your project gets equipment quickly instead of waiting on factory lead times.
Check availabilityOne compact platform, eight capacities.
Every MiniPAC uses Bry-Air's EcoDry metal silicate fluted desiccant rotor, with independent process and reactivation blowers and electric reactivation. Pick a model to see its data.
Moisture removal capacity
lb/hr at entering air of 75°F and 100 gr/lb. Select a bar to view that model.
| Model | Process CFM | Process ESP (in. WC) | React. CFM | React. heater kW | Power V/Ø/Hz | MCA / MOCP / FLA | Removal lb/hr | Weight lb | A × B × C (in) |
|---|
Data from Bry-Air MiniPAC Technical Data Sheet DC0028, rev. 6/2/2026. All data subject to change without notice. Full dimensional drawings, performance and fan curves are included with every quote.
How a MiniPAC pulls water out of the air.
Two airstreams pass through one slowly turning desiccant rotor. Process air from your space crosses three quarters of it and leaves dry. Heated reactivation air crosses the remaining quarter in the opposite direction and carries the captured water outdoors. Enter your inlet conditions to see what a MiniPAC delivers.
Process inlet
Estimates from Bry-Air MiniPAC performance data at sea level and nominal process airflow, with 3°F (1.7°C) fan heat included. Final performance is confirmed with your quote.
Every component in one compact cabinet.
Every component is reachable from the front, with 24 in. of clearance for electrical and rotor service.
- 1Front access panelIndicator lights, auto / off / manual switch, and duct collars with manual volume dampers.
- 2FiltersHigh-capacity metallic mesh filters on both the process and reactivation inlets.
- 3Desiccant rotorEcoDry metal silicate fluted media, stainless perimeter flange, PTFE bulb seals and a geared drive motor.
- 4Reactivation heaterElectric heater that regenerates the rotor, with cool-down safety and optional PID modulation.
- 5Process fanMoves air from your space through three quarters of the rotor and back to the space, with its own motor and volume damper.
- 6Reactivation fanA separate fan and motor that pulls air across the heater and through the reactivation quarter, then exhausts it outdoors.
- 7CabinetCNC-fabricated, powder-coated steel with insulated airflow sectors and a base frame.
Industrial build in a small footprint.
CNC-fabricated, powder-coated cabinets with low volume and weight per CFM, so MiniPAC fits mechanical rooms, ceilings and retrofits where a large DH unit cannot.
Metal silicate rotor
High-performance fluted media with a stainless steel perimeter flange. Non-flammable, with organics under 2%, and water washable.
Long-life sealing
PTFE-bonded bulb seals and a hard-face coated rotor edge keep air leakage low and extend seal life.
Independent airflows
Separate blower and motor for process and reactivation air, each with a volume control damper.
Built-in safeties
Reactivation airflow pressure switch, cool-down protection, and electrical interlocking of fans, heaters and rotor drive.
Easy to service
Front rotor and electrical access, auto / manual mode selection, and insulated airflow sectors.
Fast parts
Replacement parts are kept in stock and shipped quickly to keep your unit running.
Where desiccant dehumidification earns its place.
Desiccant units keep removing moisture at low temperatures and low dew points, where refrigerant dehumidifiers lose capacity. These are the projects we support most.
A Canadian partner for a proven product.
Bry-Air has built desiccant dehumidifiers since 1964. Drynex brings the MiniPAC line to Canadian contractors, engineers and owners with local pricing, engineering support and start-up.
Every selection is reviewed by a licensed professional engineer before it is quoted.
How a project works
Send your requirements
Airflow, target RH or dew point, voltage and options through the quote form, or send us your drawings and schedule.
Selection and quote
We size the unit, confirm performance at your design conditions, and send a quote with the technical data sheet.
Order and submittals
Submittal data, dimensional drawings and wiring information for engineer review.
Delivery and start-up
Shipped to site, with virtual start-up and ongoing parts and service support.
Your quote request is ready to send.
Copy the summary below and email it to sales@drynex.ca, or use the email button.